Summer Closure - RTA SRL
Dear Customer,
We hereby inform you that RTA SRL will be closed from Monday 04th of August 2025 to Sunday 24th of August 2025 - both included. All purchases received from 26th of July 2025 to Sunday 24th of August 2025 will be managed from 25th of August 2025.
Thank you for your cooperation,
Best regards
RTA SRL
CSD J4 model is fitted into a metallic box of 90 x 99 x 30 mm. It is equipped with plug-in connectors, separated for power and logic sections. It is able to drive motors up to 4.4 Amps nominal current and it is the perfect choice for low-power applications needing a programmable motion controller. A dedicated input allows setting motor speed by means of analog signal (0-5 VDC; 0-10 VDC).
RTA’s CSD series features low power bipolar ministep drives. It is based on 2 families with different possibilities of command and interface.They are characterized by a limited power range, small dimensions and easy setup. CSD series drives provide the traditional high quality and reliability of RTA, but also a very competitive price. All models are equipped with Chopper systems featuring high performance Mosfet power stage, microstepping up to 3.200 step/rev for Step&Direction models and up to 4.000 step/rev for Programmable models.
* Version: drive housed in a metallic box 90 x 99 x 30 mm, equipped with plug-in connectors.* Range of operating voltages: 24-48 VDC.
* Range of current: 2.6-4.4 Amp. Setting up to four possible values by means of a serial line.
* Microstepping: 400, 800, 1.600, 3.200 and 500, 1.000, 2.000, 4.000 steps/revolution. Setting by means of a serial line.
* Automatic current reduction at motor standstill.
* Protections:
-Protection against under-voltage and over-voltage.
-Protection against a short-circuit at motor outputs.
-Overtemperature protection with thermal sensor.
* Electronic damping facility for further acoustic noise and mechanic vibrations reduction.
* Possibility to set Pull-UP or Pull-Down inputs.
* Warranty: 24 months.
* Target speed setting by means of analog input sampled at the beginning of the motion sequence (before motor starts running).
* Input setting: 0-5 VDC or 0-10 VDC
* Frequency range:
- 3000 Hz - 48000 Hz (with ramp)
- 0 Hz - 4100 Hz or 0 Hz - 510 Hz (without ramp)
* Possibility of matching with potentiometers of 2.2 KOhm.
* Communication through RS485 serial line; up to 48 can be connected on a single serial line. One instruction can be broadcasted to all drives.
* Various type of available instructions, as for example: indexed run with ramp, free run with ramp, indexed run without ramp, run with a programmable braking distance, zero research. Space can be programmed in relative or absolute mode (linear or circular).
* Number of steps for indexed ramp up to ± 8.338.607 in relative or absolute mode, speed from 1 to 24.000 Hz in standard resolution and from 1 to 48.000 Hz in high resolution, ramp times from 16 to 1440 msec.
* Availability of instructions to developmotion programs as, for example: conditional jump time delay, program block and recovery, I/O management, , FOR NEXT loop.
* Possibility to control the execution of 8 previously stored motion programs through hardware inputs. Accordingly, the drive can be used in stand-alone applications, without serial connection.
* 8 inputs and 3 outputs, all optically insulated. Among them 1 inputs and 1 outputs are freely programmable.
* Memory of 128 instructions kept also at drive switched-off and three run time instructions.
* A utility working in Windows® is available in order to ease motion programs development by the user.
